사용 설명서 필립스 QG3150 이발기

사용 설명서

ENGLISH

General description (Fig. 1)

A Handle

B Setting indicator

C On/off switch

D Socket for appliance plug

E Micro shaver

F Hair clipping comb

G Setting selector

H Nose/ear hair trimmer

I Precision timmer

J Cutting element

K Beard trimming comb

L Cleaning brush

M Adapter

N Appliance plug

O Charging light

P Stand

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

Make sure the adapter does not get wet.

Warning

Check if the voltage indicated on the adapter and on

the appliance corresponds to the local mains voltage

before you connect the appliance.

Keep the appliance, charging stand and adapter dry.

The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug, as

this causes a hazardous situation.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

Caution

Use, charge and store the appliance at a temperature

between 15°C and 35°C.

Only use the adapter supplied to charge the

appliance.

If the adapter is damaged, always have it replaced

with one of the original type in order to avoid a

hazard.

Do not use the appliance when one of the

attachments or combs is damaged or broken as this

may cause injury.

Be careful with hot water. Always check if the water

is not too hot, to prevent your hands from getting

burnt.

This appliance is only intended for clipping human

scalp hair and for trimming and grooming the human

beard, moustache, sideburns, nose hair and ear hair.

Do not use it for another purpose.

Never try to trim your eyelashes.

If the appliance is subjected to a major change in

temperature, pressure or humidity, let the appliance

acclimatise for 30 minutes before you use it.

Compliance with standards

This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this

user manual, the appliance is safe to use based on

scientic evidence available today.

Preparing for use

Charging

Charge the appliance for at least 10 hours before you use

it for the rst time and after a long period of disuse.

When the appliance is fully charged, it has a cordless

operating time of up to 35 minutes. Do not charge the

appliance for more than 24 hours.

The appliance does not run from the mains.

You cannot charge the appliance in the stand.

1 Insert the appliance plug into the socket of

the appliance and put the adapter in the wall

socket (Fig. 2).

The charging light on the adapter goes on to

indicate that the appliance is charging (Fig. 3).

Note: The charging light does not change colour and does

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

,

not go out when the appliance is fully charged.

Optimising the lifetime of the rechargeable

battery

Remove the adapter from the wall socket when the

battery is fully charged (which takes 10 hours).

Do not leave the appliance plugged into the wall

socket for more than 24 hours.

Discharge the battery completely twice a year

by letting the motor run until it stops. Then fully

recharge the battery.

Attaching/detaching attachments

All attachments (cutting element, precision trimmer, micro

trimmer, micro shaver and nose/ear hair trimmer) can be

attached and detached in the same way.

1 To attach the attachment, push it onto the handle

(‘click’) (Fig. 4).

2 To detach the attachment, pull it off the

handle. (Fig. 5)

Hair clipping

Preparing for hair clipping

Make sure that the appliance is fully charged when you

start clipping.

It is not possible to run the appliance from the mains.

Only use the appliance on clean, dry hair. Do not use it

on freshly washed hair.

1 Make sure that the head of the person whose hair

you intend to cut is at the same level as your chest.

This ensures that all parts of the head are clearly

visible and within easy reach.

2 Comb the hair in the direction of growth (Fig. 6).

3 Put the cutting element on the handle (see

section ‘Attaching/detaching attachments’ in chapter

‘Preparing for use’).

Clipping with hair clipping comb

1 Slide the hair clipping comb into the guiding

grooves on both sides of the handle (‘click’) (Fig. 7).

2 Press the setting selector upwards or downwards

to set the desired setting (Fig. 8).

The setting indicator on the back of the appliance

shows the selected setting. (Fig. 9)

The table shows how long the hair will be after clipping at

the different settings.

When you clip for the rst time, start at the highest

setting (9) to familiarise yourself with the appliance.

Settings of hair clipping comb

Setting Hair length after clipping

1 4mm

2 6mm

3 8mm

4 10mm

5 12mm

6 14mm

7 16mm

8 18mm

9 20mm

Tip: Write down the hair length settings you have used to

create a certain hairstyle as a reminder for future clipping

sessions.

3 Switch on the appliance.

4 Move the appliance through the hair slowly.

To clip in the most effective way, move the appliance

against the direction of hair growth.

Since all hair does not grow in the same direction,

you need to move the appliance in different

directions (upward, downward or across) (Fig. 10).

Make sure that the at part of the comb is always

fully in contact with the scalp to obtain an even

result.

Make overlapping passes over the head to ensure

that you cut all the hair that needs to be cut.

To achieve a good result with curly, sparse or long

hair, use a comb to guide the hair towards the

appliance.

5 Regularly remove cut hair from the comb.

-

-

-

,

-

-

-

-

-

If a lot of hair has accumulated in the comb, remove the

comb from the appliance and blow and/or shake the hair

out of it.

Contouring without hair clipping comb

You can use the appliance without hair clipping comb to

clip hair very close to the skin (0.6mm) or to contour the

neckline and the area round the ears.

Be careful when you clip without comb because the

cutting element removes every hair it touches.

1 Press the setting selector upwards and pull the

comb off the handle. (Fig. 11)

2 Before you start to contour the hairline round the

ears, comb the hair ends over the ears.

3 Tilt the appliance in such a way that only one edge

of the cutting element touches the hair ends when

you shape the contours round the ears (Fig. 12).

Only cut the hair ends. The hairline should be close to

the ear.

4 To contour the neckline and sideburns, turn the

appliance and make downward strokes (Fig. 13).

Move the appliance slowly and smoothly. Follow the

natural hairline.

Trimming

Preparing for trimming

Make sure that the appliance is fully charged before you

start trimming.

It is not possible to run the appliance from the mains.

1 Comb the hair to be trimmed (beard, moustache,

sideburns, eyebrows) with a ne comb.

2 Put the cutting element on the handle (see section

‘Attaching/detaching attachments’ in chapter

‘Preparing for use’).

Beard trimming with beard trimming comb

1 Slide the beard trimming comb into the

guiding grooves on both sides of the handle

(‘click’) (Fig. 14).

2 Press the setting selector upwards or downwards

to set the desired setting (Fig. 15).

The setting indicator on the back of the appliance

shows the selected setting.

The table shows how long the hair will be after trimming

at the different settings.

When you trim for the rst time, start at the highest

setting (9) to familiarise yourself with the appliance.

Settings of beard trimming comb

Settings Hair length after trimming

1 2mm

2 4mm

3 6mm

4 8mm

5 10mm

6 12mm

7 14mm

8 16mm

9 18mm

3 Switch on the appliance.

4 Move the appliance through the hair slowly (Fig. 16).

To trim in the most effective way, move the appliance

against the direction of hair growth.

Since all hair does not grow in the same direction,

you need to move the appliance in different

directions (upward or across).

Make sure that the at part of the comb is always

fully in contact with the skin to obtain an even result.

5 Regularly remove cut hair from the comb.

If a lot of hair has accumulated in the comb, remove the

comb from the appliance and blow and/or shake the hair

out of it.

Trimming at the ‘stubble look’ setting

1 To create a ‘stubble look’, trim with the beard

trimming comb set to hair length setting 1. (Fig. 17)

,

-

-

-

4239.000.5873.2

등급

이 설명서에 대한 추가 정보

필립스 QG3150 이발기에 대한 종이 설명서가 있으면 좋다고 생각합니다. 언제든지 당사 웹사이트에서 설명서를 다운로드하여 직접 인쇄하실 수 있습니다. 원본 설명서를 원하시면 Philips에 문의하시기 바랍니다. 원본 매뉴얼을 제공할 수도 있습니다. 다른 언어로 된 필립스 QG3150 이발기 설명서를 찾고 계십니까? 홈페이지에서 원하는 언어를 선택하고 모델 번호를 검색하여 사용 가능한지 확인하세요.

명세서

필립스 이발기에 대한 모든 매뉴얼
이발기의 추가 매뉴얼

필립스 QG3150 이발기에 대해 자주 묻는 질문

저희 지원 팀은 자주 묻는 질문에 대한 유용한 제품 정보 및 답변을 찾고 있습니다. 자주 묻는 질문에 오류를 발견하신다면, 연락 양식에 따라 알려주시기 바랍니다.

관련 상품

사용 설명서

필립스 QG3389 이발기

사용 설명서

필립스 QG3385 이발기

사용 설명서

필립스 HC3522 이발기

사용 설명서

필립스 QG3060 이발기

사용 설명서

필립스 QC5375 이발기

사용 설명서

필립스 HC5612 이발기

사용 설명서

필립스 HC3588 이발기

사용 설명서

필립스 QG3250 이발기

관련 카테고리