사용 설명서 필립스 QG3060 이발기

사용 설명서

ENGLISH

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips offers,

register your product at www.philips.com/welcome.

General description (Fig. 1)

A 2D Contour Tracking beard trimming comb

B Trimming attachment

C Hair length selector

D Release button

E On/off slide

F Socket for appliance plug

G Cleaning brush

H Barber’s comb

I Charging light

J Adapter

K Appliance plug

L Nose/ear/eyebrow attachment

M Charging stand with storage facility

N Precision attachment (HQG267/QG3040 only)

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

- Make sure the adapter does not get wet.

Warning

- Check if the voltage indicated on the appliance

corresponds to the local mains voltage before you

connect the appliance.

- The adapter contains a transformer. Do not cut

off the adapter to replace it with another plug, as

this causes a hazardous situation.

- This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

- Children should be supervised to ensure that they

do not play with the appliance.

Caution

- Do not immerse the appliance in water or any other

liquid, nor rinse it under the tap.

- Use, charge and store the appliance at a temperature

between 15°C and 35°C.

- Only use the adapter supplied.

- Do not use a damaged adapter.

- If the adapter is damaged, always have it replaced

with one of the original type in order to avoid a

hazard.

- Do not use the appliance if one of the attachments

or combs is damaged or broken, as this may cause

injury.

- This appliance is only intended for trimming the

human beard, moustache, sideburns, nose hair,

ear hair and eyebrows. Do not use it for another

purpose.

- Never try to trim your eyelashes.

- If the appliance is subjected to a major change in

temperature, pressure or humidity, let the appliance

acclimatise for 30 minutes before you use it.

Compliance with standards

- This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this

user manual, the appliance is safe to use based on

scientic evidence available today.

Preparing for use

Charging

Charge the appliance for at least 10 hours before you use

it for the rst time and after a long period of disuse.

When the appliance is fully charged, it has a cordless

operating time of up to 35 minutes.

Do not charge the appliance for more than 24 hours.

Note: The appliance is not suitable for mains operation.

You can charge the appliance in 2 different ways:

Charging in the charging stand

1 Make sure the appliance is switched off.

2 Insert the pin of the appliance plug into the opening

in the bottom of the stand (1) and push the plug

sideways to lock it into place (2) (Fig. 2).

3 Place the appliance in the charging stand on the

appliance plug (Fig. 3).

4 Put the adapter in the wall socket.

, The charging light goes on. The light stays on

as long as the appliance is connected to the

mains (Fig. 4).

Charging outside the charging stand

1 Make sure the appliance is switched off.

2 Insert the appliance plug into the socket of the

appliance (Fig. 5).

3 Put the adapter in the wall socket.

, The charging light goes on. The light stays on

as long as the appliance is connected to the

mains (Fig. 4).

Optimising the lifetime of the rechargeable

battery

- Do not leave the appliance plugged into the wall

socket for more than 24 hours.

- Discharge the battery completely twice a year

by letting the motor run until it stops. Then fully

recharge the battery.

Using the appliance

Note: Always comb the hair with a ne comb in the hair

growth direction before you start trimming.Make sure that

the hair is dry and clean.

Beard trimming with comb

1 Put the beard trimming comb on the trimming

attachment and push it home (‘click’) (Fig. 6).

2 Press the hair length selector and slide it to the

desired setting. See the table below (Fig. 7).

The selected setting appears in the window to the left of

the hair length selector.

- When you trim for the rst time, start at the highest

setting (9) to familiarise yourself with the appliance.

- To create a ‘stubble look’, trim with the beard

trimming comb set to hair length setting 1.

Settings of the beard trimming comb

Setting Hair length after trimming

1 2mm

2 4mm

3 6mm

4 8mm

5 10mm

6 12mm

7 14mm

8 16mm

9 18mm

3 To trim most effectively, move the appliance against

the hair growth direction (Fig. 8).

Do not move the appliance too fast. Make smooth and

gentle movements and make sure the surface of the

comb always stays in contact with the skin.

If a lot of hair has accumulated in the comb, remove the

comb from the appliance and blow and/or shake the hair

out of it.

Note: You have to set the hair length selector to the

desired setting again after you have removed the comb.

Beard trimming without comb

Trimming without the comb results in a very short

stubble beard.

1 Press and slide the hair length selector upwards (1)

and pull the beard trimming comb off the appliance

(2) (Fig. 9).

Note: Never pull at the exible top of the comb. Always pull

at the bottom part.

2 Make well-controlled movements and touch your

beard only lightly with the trimming attachment.

Using the precision attachment (HQG267/

QG3040 only).

You can use the precision attachment to dene the

contours of your beard, moustache and sideburns.

1 Press and slide the hair length selector upwards

(1) and pull the beard trimming comb off the

appliance (2) (Fig. 9).

Note: Never pull at the exible top of the comb. Always pull

at the bottom part.

2 Press the release button (1) and pull the trimming

attachment off the appliance (2) (Fig. 10).

3 Put the precision attachment on the

appliance (Fig. 11).

4 Hold the appliance upright when you use the

precision attachment (Fig. 12).

Grooming nose hair, ear hair and eyebrows

1 Press and slide the hair length selector upwards (1)

and pull the beard trimming comb off the appliance

(2) (Fig. 9).

Note: Never pull at the exible top of the comb. Always pull

at the bottom part.

2 Press the release button (1) and pull the trimming

attachment off the appliance (2) (Fig. 10).

3 Put the nose/ear/eyebrow attachment on the

appliance (‘click’) (Fig. 13).

Trimming nose hair

1 Make sure your nostrils are clean.

2 Switch on the appliance and insert the tip of the

trimmer into one of your nostrils (Fig. 14).

Do not insert the tip more than 0.5cm into your nostril.

3 Slowly move the tip in and out while turning it

round at the same time to remove unwanted hair.

To reduce the tickling effect, make sure that you press the

side of the tip rmly against the skin.

Trimming ear hair

1 Clean the outer ear channel. Make sure it is free

from wax.

2 Switch on the appliance and move the tip softly

round the ear to remove hairs that stick out

beyond the rim of the ear (Fig. 15).

3 Carefully insert the tip into the outer ear

channel (Fig. 16).

Do not insert the tip more than 0.5cm into the ear

channel as this could damage the eardrum.

Trimming eyebrows

Use the tip to cut individual eyebrow hairs.

Do not use the appliance to dene or trim the entire

eyebrow.

1 Place the tip of the attachment on the upper edge

of the eyebrow.

2 Move the tip of the attachment along the edge of

the eyebrow from the base of the nose towards the

outer tip of the eyebrow (Fig. 17).

Cleaning

Never use scouring pads, abrasive cleaning agents or

aggressive liquids such as alcohol, petrol or acetone to

clean the appliance.

Note: The appliance does not need any lubrication.

Clean the appliance every time you have used it.

1 Make sure the appliance is switched off and

disconnected from the mains.

2 Remove any comb and/or attachment from the

appliance.

3 Blow and/or shake out any hair that has

accumulated in the attachment and/or comb.

4 Clean the outside and inside of the attachment

with the brush cleaning brush (Fig. 18).

2

4222.002.8130.1

등급

이 설명서에 대한 추가 정보

필립스 QG3060 이발기에 대한 종이 설명서가 있으면 좋다고 생각합니다. 언제든지 당사 웹사이트에서 설명서를 다운로드하여 직접 인쇄하실 수 있습니다. 원본 설명서를 원하시면 Philips에 문의하시기 바랍니다. 원본 매뉴얼을 제공할 수도 있습니다. 다른 언어로 된 필립스 QG3060 이발기 설명서를 찾고 계십니까? 홈페이지에서 원하는 언어를 선택하고 모델 번호를 검색하여 사용 가능한지 확인하세요.

명세서

필립스 이발기에 대한 모든 매뉴얼
이발기의 추가 매뉴얼

필립스 QG3060 이발기에 대해 자주 묻는 질문

저희 지원 팀은 자주 묻는 질문에 대한 유용한 제품 정보 및 답변을 찾고 있습니다. 자주 묻는 질문에 오류를 발견하신다면, 연락 양식에 따라 알려주시기 바랍니다.

관련 상품

사용 설명서

필립스 HC3530 이발기

사용 설명서

필립스 HC3518 이발기

사용 설명서

필립스 HC3588 이발기

사용 설명서

필립스 HC3536 이발기

사용 설명서

필립스 QG3378 이발기

사용 설명서

필립스 QC5370 이발기

사용 설명서

필립스 QG3250 이발기

사용 설명서

필립스 QG3391 이발기

관련 카테고리