사용 설명서 필립스 GC9140 다리미

사용 설명서

Problem Possible cause and solution

The Auto Calc Clean process is activated. Wait for approximately 4

minutes for the appliance to be ready for steam ironing.

Water droplets come

out of the soleplate

When you start steam ironing and when you continue steam ironing

after an interruption, the steam that was still present in the supply hose

has cooled down and condensed into water. This causes water droplets

to come out of the soleplate. This happens sometimes when you start

ironing or continue ironing after an interruption. Hold the iron over an

old cloth and press the steam trigger. Wait until steam instead of water

comes out of the soleplate.

The set temperature is too low for steam ironing. Set a temperature of

2 or higher.

The wet spots that appear on your garment after you have steam ironed

for some time may be caused by steam that has condensed onto the

ironing board. Iron the wet spots without steam for some time to dry

them. If the underside of the ironing board is wet, wipe it dry with a

piece of dry cloth.

Steam may have condensed in the hose, the temperature may have been

set below 3 or the appliance may not be ready for steam ironing.

Flakes and impurities

come out of the

soleplate or the

soleplate is dirty.

Impurities or chemicals present in the water have deposited in the steam

vents and/or on the soleplate. Clean the soleplate with a damp cloth.

The appliance

produces a pumping

sound.

Water is pumped into the boiler inside the steam generator. This is

normal. However, if the pumping sound does not stop, switch off the

appliance immediately and unplug it. Contact an authorised Philips

service centre.

Water leaks out of the

steam generator.

The Calc Clean tank has overowed during the Auto Calc Clean process.

Always empty the Calc Clean tank after the Calc Clean process. This

prevents the Calc Clean tank from overowing the next time the auto

Calc Clean process is performed.

The appliance

occasionally produces

a loud pumping noise

and clicking sound.

This happens during the Auto Calc Clean process. Water is pumped

from the water tank into the steam generator, and expelled into the Calc

Clean tank. Wait a few minutes for the appliance to complete the Auto

Calc Clean process. Empty the Calc Clean tank and then top up the

water tank. The Auto Calc Clean process is a normal process that is

performed automatically at regular intervals.

I cannot place the iron

on its heel.

To make the appliance more ergonomic, it has been designed in such a

way that the iron can only be put down horizontally. Place the iron

horizontally on the heat-resistant iron resting mat. The mat can be left on

top of the steam generator or you can place the mat on the ironing

board. Do not place the hot iron directly onto the ironing board without

the heat-resistant iron resting mat.

The appliance beeps

continuously.

The water tank has gone empty during the Auto Calc Clean process. Fill

the water tank.

10

등급

이 설명서에 대한 추가 정보

필립스 GC9140 다리미에 대한 종이 설명서가 있으면 좋다고 생각합니다. 언제든지 당사 웹사이트에서 설명서를 다운로드하여 직접 인쇄하실 수 있습니다. 원본 설명서를 원하시면 Philips에 문의하시기 바랍니다. 원본 매뉴얼을 제공할 수도 있습니다. 다른 언어로 된 필립스 GC9140 다리미 설명서를 찾고 계십니까? 홈페이지에서 원하는 언어를 선택하고 모델 번호를 검색하여 사용 가능한지 확인하세요.

명세서

필립스 다리미에 대한 모든 매뉴얼
다리미의 추가 매뉴얼

필립스 GC9140 다리미에 대해 자주 묻는 질문

저희 지원 팀은 자주 묻는 질문에 대한 유용한 제품 정보 및 답변을 찾고 있습니다. 자주 묻는 질문에 오류를 발견하신다면, 연락 양식에 따라 알려주시기 바랍니다.

관련 상품

사용 설명서

필립스 GC7420 다리미

사용 설명서

필립스 DST8030 Azur 다리미

사용 설명서

필립스 PSG6022 PerfectCare 다리미

사용 설명서

필립스 GC4515 Azur Performer Plus 다리미

사용 설명서

필립스 GC9415 다리미

사용 설명서

필립스 GC9625 다리미

사용 설명서

필립스 DST3020 다리미

사용 설명서

필립스 GC8638 다리미

관련 카테고리